浦东江西聚氨酯车库地坪哪家好

浦东江西聚氨酯车库地坪哪家好 Epoxy mortar floor coating system with resistance to stress, impact resistance, high wear resistance, high mechanical strength, resistance to chemical corrosion, low shrinkage, anti moisture, root Zelkowa acuminata need to do surface smooth or slippery surface.Basic level conditionBasic needs to have sufficient strength (compressive strength of at least 30 n / mm). Surface level, fine cut, compacting and drying (water below 4%), no loose particles. Tensile strength not less than 1.5 N / mm2. More than four kinds of choice can be more workshop floor of the painting, of course, in addition to hardening wear-resisting floor, a construction, trailer truck rolling sand can not afford 30 years, no dust, cost reasonable, good performance. Contact: 4oo-o7o9-91oStatement: the choice of epoxy floor paint and the surface thickness of the match is not relative to the decision, you can do according to a reasonable standard, can not be in accordance with the above requirements to choose.Warm tip: suitable for workshop floor coating floor technology different, choose a higher price and suitable for their own is the most important, especially when foundation ground hardness is not up to the standard and the surface smoothness is poor when they need to consider what kind of floor paint, when although floor paint thickness of choice is also very important.Surface preparationShall be by mechanical methods, such as sand milling, completely remove the insufficient strength of the loose layer and oil layer and used a vacuum cleaner to suck out the loose sand.blendPre stir A components. In proportion to the A and B, with low speed electric mixer stirring, (the speed of 300-400 / min). Stir at least 3 minutes until evenly mixed material into a clean container.Application methodPremix is strip dumped on the surface, with a rubber brush uniformly smooth. When the self leveling mortar is used for construction, the screw roller is used for bleeding. Sprinkle dry sand (0.4-0.7 mm) on the bottom layer of finished construction. Dry after removal of excess sand, the surface should be filled with sand in order to achieve the best visual effect, reduce material consumption. Cleaning out the dust on the surface with an industrial vacuum cleaner. With a rubber roller or brush surface coating construction.The environment and the base temperature is lowest, 10 (at least dew point temperature is above 3 degrees Celsius).Adequate ventilation shall be provided for the construction and solidification of indoor, ditch, and shaft. Stay away from open flames and other flammable media, such as welding.In the light of the weak, only use safe electric light, ventilation equipment need to have fire protection device.环氧沙浆
地坪涂装体系具有耐重压,耐冲击,高耐磨耗,高机器强度,耐普通化学腐蚀,缩短率小,抗必定的潮气,可根椐需求做滑润外观或防滑外观。底层情况 底层需有餍足强度(抗压强度至少为30牛顿/平方毫米)。外观需水平,细琢,密实,干燥(水分低于4%),无松懈颗粒。抗拉强度不低于1.5牛顿/ mm2。以上四种遴选可以

呐喊针对更多厂房车间地上的涂装,固然
除此以外还有硬化耐磨地坪,一次施工,拖车叉车碾压30年不起砂,不起尘,造价合理,机能好。联系
:4oo-o7o9-91o声明:以上对环氧树脂地坪漆的遴选和
地上厚度的婚配不是相对决议的,可以

呐喊遵照合理的规范去做,不必定可以

呐喊遵照以上规则去遴选。温馨提示:合适做厂房车间地上涂装的地坪工艺简约,遴选一个性价比较高且合适自己的较为重要,尤其是当根底地上硬度不合格且地上平坦度叫差的时分就需求好好考虑运用哪一种地坪漆,固然
地坪漆厚度的遴选也是适当重要。外观预备须用机器办法(如砂铣)彻底革除强度不行的松懈层和油污层,用真空吸尘器吸掉松懈的砂子。混杂 预先拌和A组份。按份额混杂A与B,用低速电动拌和机拌和,(拌和速度为300-400转/分)。较少拌和3分钟直至平均,将混杂物料倒入一洁净容器中,再稍做拌和。运用办法 预拌料呈条状倾倒在基面上,用一橡胶刷帚平均抹平。施工自流平沙浆
时,运用钉状滚筒放气。在刚施工完的底层涂层上撒上干砂(0.4-0.7毫米)。干固后 需革除残存的砂子,外观应充溢砂以到达较好的视觉效果,降落
物料的耗费。用工业用的真空吸尘器革除去外观的尘埃。用滚筒或橡胶刷帚施工面层涂层。环境和底基温度 较低: 10℃ (至少露水点温度3℃以上)在室内,沟洼,竖井处施工和固化过程中,须供给餍足的通风。远离明火和其他易燃媒体,如焊接。在光泽强大的当地,只可运用安全电灯,通风装备
需有防火花装备